call me insane!!

[2fast4u]

does anybody have any fist hand experience with this setup or similar

1005/2y (2-turn motor from aveox)

L160rc (speed control from then to)

and a innocent b3

i need 2 no if this will work

[Nicks $700.00 Pede]

ill i have to say is i dont know but heres my opinion.....
http://www.rccaraction.com/ubb/eek.gif holy crap thats goig to be **** fast!!!!! zzzzzzzzzcrunch sorry mr. turn mrshal ill pay your doctors bill. Umm.... Mr. Marshal?? You alive??? Nope. I didnt do it http://www.rccaraction.com/ubb/biggrin.gif lets see about 100mph???? better be using 3000s or is this case 300000s


------------------
All I have to say in my signature is I like big, bad, fast, tall, and unstoppable r/c trucks....Stampede The Ultimate Jump Truck:D

[oldtimeRCer]

oooooooooooK your INSANE

------------------
I may grow older but I'll never grow up.

R/C is a way of life

3 Tamiya TA02 Sedan's, XXT Sport, XX Sport, RC10T3, 2 Bulleads,

[Justin Thyme]

No bout a doubt it, that's pretty insane for a B3!

Where did you get info on that motor and ESC? Does Aveox have a website?

[2fast4u]

ya its www.aveox.com (http://www.aveox.com)

[2fast4u]

ow ya i forgot they also have single turn motors and costom winds available!!!!!!!!

[2fast4u]

DID I MENTION THE AVERAGE EFFECENCY ON THEM IS OVER 85% !!!!! SO RUN TIME WITH 3000, 2400 WOULD BE TO BAD AND THE DON'T DRAW VERY HIGH AMPERAGE

[BrahmaBullSQ]

it'll be a dream come true if it works!!!

opponent http://www.rccaraction.com/ubb/eek.gif
u http://www.rccaraction.com/ubb/tongue.gif

[This message has been edited by BrahmaBullSQ (edited 09-18-2000).]

[highguy31]

VROOOOOOOOOOOOOOOOOOM............WATCH OUT........AHHHHHHHHHHHH

[R_C_MAN]

I guess you are insane look at the prices of those motors.

------------------
I like my R/C trucks fast dont you?

[hpiguy]

Motors with that low of a winding are almost like a dead short on the batteries. So don't look for long runtimes, or battereis to hold up too long period.

Better have a good ESC with good shut down circuitry, and make sure you gear it so you don't have to push start the car. Those motors aren't exactly torque machines off the line.

They are designed for airplane props and boats, that require little torque to get moving.

But give it a shot, and let us know what or what doesn't happen.

BTW better lower your B3 to the ground or use an onroad car with a huge spur gear.

Hope it all works out.

[2fast4u]

hpiguy

you have to buy there speed controls because the motors have something like 5 or 6 wires comming out

ps i was thinking 2 3000 packs wired so its like a 6000 pack!!

and i hope i get that job at mcdonalds!! :-)

[tc3guy]

2fast4u

you can wire two 3000 packs together but it wont increase the packs mah but it will increse the voltage your packs put out and runtimes will go down

[2fast4u]

if you wire them differently it will increse the run just have the 2 + on the packs go to the + on the speed control and 2 - go to the-on speed control

[hpiguy]

Parallel is definetily the way to go.

I run my Clod this way, I use two 2000 packs to make 4000 mah. It runs over an hour on the stock motors.

I'm sure the guy was thinking of wiring in series, which would double the voltage and reduce the runtime.

[2fast4u]

i've just ran into a problem i can't get in touch with the jerks at aveox so i don't know if it will work but i know of 1 motor that will work but it is comparable to a 14 turn motor i'm interested in the one cliff lett used to go 94.22 mph!!! in '97 i know its the H60 but i don't know how to mount it and i don't want to spend $150 on a motor i can't use so if anydody knows how to contact cliff lett other then snail mail let me know

[hpiguy]

I think Cliff still works at Associated.

If not they might know how to get ahold of him.

[R_C_MAN]

Who is Cliff and how do you know he went 90 some miles per hour.

------------------
I like my R/C trucks fast dont you?

[hpiguy]

It's from the days when RCCa covered oval. Oval used to be huge, especially big paved ovals.

Thunderdrome was killer.

Cliff is old school racer stuff. I think he still races but he was like Kinwald and Saxton is now.

He set record speeds on ovals, and even was going so fast he had special tires made to keep them from flying apart.

"Another reason for RCCA to make a CD collection of the previous years, it would be a good seller. MAD fit 30+ years on four disks, including any and all pics"

[R_C_MAN]

Where can you get this CD collection.

[2fast4u]

actually i saw it on the team associated '97 video cliff doing 94.22 mph!! the the diff axel broke another guys tire riped a hole in his car when it got to speed!!!

[2fast4u]

i just thought about it and i think i'm going to make a funny car,... whos speed is nothing to laugh about!!!

[ou812]

R/C Boat guys use Aveox motors a lot. You may try the message boards at www.rumrunnerracing.com (http://www.rumrunnerracing.com) for someone who'e actually used one of these beasts.

------------------
Oh, you ate one too?
NRS4-2, RS4 Sport, RC10-GT, and a Clod
Am I bragging? Nope. Just tellin' you what I've got. :)

[hpiguy]

That CD collection isn't available yet.

Go to the Mag forums and ask for it.